The seat.
Shopping list (sizes including loop and/or hem):
- 1x 2 piece buckle for 4 cm wide seatbelt webbing (B1 and B2)
- 2x 2 piece buckle for 2.5 cm wide seatbelt webbing (A1-A2)
- 1x 180 cm seatbelt FLEXIBLE webbing, 4 cm wide, black
(The seatbelt webbing of a car is stiff compared to the webbing used for a sportsbag.)
- 1x 500 cm seatbelt webbing, 2.5 cm wide, black
- 1x 130 cm seatbelt webbing, 2.5 cm wide, red
- thread thick or normal size.
Warnings:
- Picture is a look a like.
- All sizes stated in the DRAWING are without hem or noose (loop).
It is the size measured after the seat is ready !!
- Study the drawing and verify that some measures go
- top_webbing to top_webbing
- top_webbing to bottom_webbing (blue part)
- left_side_webbing to left_side-webbing (red webbing left)
- left_side_webbing to right_side-webbing (red webbing middle)
- right_side_webbing to left_side-webbing (red webbing right)
- When using THIN thread sew layers of minimal 6 threads for EACH seam !!!!!
- Cut with an electric soldering bolt the 180 cm black seatbelt webbing into:
- 1x 39 cm (blue part)
- 1x 63.5 cm (B1 side, extra: 10 cm B1 side + 10 cm to attach blue part)
- 1x 77.5 cm (B2 side, extra: 10 cm B2 side + 10 cm to attach blue part)
- Cut with an electric soldering bolt the 500 cm black seatbelt webbing into:
- 1x 32.5 cm
- 1x 86 cm (extra: 10 cm overlap over the 4 cm wide webbing)
- 1x 99 cm (extra: 10 cm overlap over the 4 cm wide webbing)
- 1x 104 cm (extra: 10 cm overlap over the 4 cm wide webbing)
- 2x 10 cm
- 2x 60 cm
- Cut with an electric soldering bolt the 130 cm red seatbelt webbing into:
- 1x 36 cm
- 2x 46 cm
- Work your way down starting on the top left "B1" side.
- 32.5 cm seatbelt webbing, 1st from top, no hem or loop.
- 86 cm seatbelt webbing, 2nd from top, loop attached fully over the 4 cm wide webbing.
- 99 cm seatbelt webbing, 3rd from top, loop attached fully over the 4 cm wide webbing.
- 104 cm seatbelt webbing, 4th from top, loop attached fully over the 4 cm wide webbing.
- Work your way down starting on the top right "B2" side.
- 32.5 cm seatbelt webbing, 1st from top, no hem or loop.
- 86 cm seatbelt webbing, 2nd from top, loop attached fully over the 4 cm wide webbing.
- 99 cm seatbelt webbing, 3rd from top, loop attached fully over the 4 cm wide webbing.
- 104 cm seatbelt webbing, 4th from top, loop attached fully over the 4 cm wide webbing.
- Attach the 39 cm seatbeld webbing (blue part) at an angle 30 degrees
- 36 cm seatbelt webbing, red, with hem at TOP around 2nd (black webbing in between)
- 46 cm seatbelt webbing, red, with hem at TOP around 1st (black webbing in between), slightly bended to the
middle at blue part.
- 46 cm seatbeld webbing, red, same as above but on the other side.
- 10 cm seatbelt webbing, 2.5 cm wide, folded double (buckle A1) and attached to the blue part on the
OUTSIDE.
- 60 cm seatbelt webbing, 2.5 cm wide, folded double (buckle A2). This part is for the rear-axle.
- Optional you can cover the blue part on the INSIDE with foam covered in some soft dacron fabric.
- Put it on the buggy. Check the fit for the B1-B2 buckle. Check the picture, the buckle is under the
downtube.
- Attack buckle B1 to bottom (blue) to B2, with 7.5 cm extra on each side for the buckle attachment.